Precise HIFU lifting at home. Manual for safe use with Medicube High Focus Shot

Medicube Age-R High Focus Shot brings the capabilities of ultrasound lifting (HIFU/MFU) from professional beauty salons directly to your home. The main technological advantage of this device is its ability to affect the 4.5 mm depth – the level of The SMAS layer, serving as a support for the entire face. Through precisely directed heat energy, the device stimulates the dermis to produce new collagen, which makes the skin visibly firmer and more elastic.

The effect of HIFU therapy can be maintained between 9 and 18 months, and the final result depends on how accurately and safely you apply the procedure. Since we work with technology that creates microscopic heat points beneath the surface, it is essential to avoid specific areas in order to preserve the natural volume and youthful contour of the face.

In this guide, we will analyze how to conduct your 12-week course step by step and why it is important to do it in advance mark your face for maximum safety. The following lines will prepare you for your first HIFU procedure at home, so that you can move from theory to practice with the necessary care and confidence.

How to prepare and set up Medicube Age-R High Focus Shot for first use?

1. Loading and first steps

First of all, the device must be fully charged. The USB-C port is located on the bottom, under a small flap. A full charge takes between 2 and 2.5 hours.

2. Inclusion and Intensity Levels

• Turn on

Back button (Power Button) The power button is located on the back of the device. When you press and hold it, the device turns on or off.

• Power levels

The power button and the one for changing the intensity levels are the same. The HIFU device automatically starts at level 1. With short presses of the same button, you can switch between the five intensity levels. The levels you switch control the strength of the thermal impulse (how „hot“ the impact point is). This allows you to adapt the procedure to your own sensitivity, which is impossible with powerful professional devices. For first-time use, it is highly recommended to start at the lowest level until you get used to the sensation.

3. Frequency control (1 Hz or 2 Hz)

Front button (Shot Button) This is a separate button that serves only to activate the ultrasonic „shots“. A short press on it activates the frequency from 1Hz (one shot per second), and if you hold it for about 2 seconds, you switch to 2Hz (two shots per second).

• 1 Hz (One shot per second)

Our advice is to start just like that because it gives you much better control over the placement of the shots and allows you to monitor how your skin reacts in real time.

• 2 Hz (Two shots per second)

Activated by holding the „shot“ button for about 2 seconds. This setting is for more advanced users as it shortens the procedure time but requires a faster and more confident technique.

Important! While professional machines deliver energy in long lines from dozens of points simultaneously, Medicube works through single, micro-precise pulses (Single Shots). This gives you full control over each point and ensures that you don't inadvertently affect adjacent areas.

4. Additional features: LED light and mobile app

The device has an LED light (usually green), the color of which can be changed via the app AGE-R Clinic. Although the app helps keep track of the number of shots, it not necessary for the operation of the device.

How to properly mark your face for maximum safety?

Since the HIFU device reaches the level of the SMAS layer and superficial fat deposits, precision is a must. With the home device Medicube Age-R High Focus Shot, the depth is preset to 4.5 mm, which requires increased attention and proper marking of areas, to avoid affecting fatty deposits and/or nerves. To ensure that the marking is accurate and easy to clean afterwards, use eyeliner.

1. Protection of cheek volume (upper fat deposits)

People with finer faces and a small amount of subcutaneous fat It is important to be cautious when treating the cheeks. The fat pads in this area serve as a natural „pad“ that lifts the lower part of the face and gives it a youthful appearance. Here’s how to protect your fat deposits if you have limited volume in the cheekbone area:

• Feel the bone of the eye socket (orbital rim) and draw the first line horizontally below it.
• Draw a second line starting from the nostril at an angle upwards towards the top of the ear.

It is recommended not to go over the marked area with the HIFU device, especially if you do not have sufficient volume in your cheekbones.

2. Protection of nerve pathways

• Mandibular nerve. Place your index finger vertically at the corner of your mouth. Mark two lines on either side of your finger down towards your jaw. This is an area you should avoid due to the risk of heat damage to the nerve.
• Temporal nerve. Find the bulge at the end of the brow bone. Draw a line from it back to the hairline and another from the arch of the brow up at the same angle. This area contains important nerves and blood vessels.
• In front of the ear. Place a finger in front of your ear and draw a vertical line down to the corner of your jaw.

3. Localization of the facial artery

• Run your finger under the lower jawbone until you feel a small indentation (notch). Mark this spot to avoid discomfort and the risk of bruising.

4. Areas of the face and neck that are not treated

•  The central part of the neck: Avoid the larynx and thyroid area.
• Face: Do not treat directly on the lips, nose, the area between the nose and mouth, or the area between the eyebrows ("the frown line").

Respecting these zones is the way to ensure professional care at home, by protecting the nerves and fat deposits responsible for the lifted facial contour.

Important! The visual map of areas to avoid, marked with an „X“ symbol, makes home use of the HIFU device completely predictable and safe.

Application technique

1. Conductive gel preparation

Before touching the skin with the HIFU device Medicube Age-R High Focus Shot, you should apply a generous amount conductive gel on the areas to be treated. It ensures the correct conduction of the ultrasound and helps the head of the device to glide smoothly. It is recommended to use Age-R Booster Gel, which is specially developed for the Medicube series of devices. This gel not only provides the necessary conductivity, but can also be left on the skin after the procedure to absorb like a serum, providing additional hydration and shine.

2. Slipping technique

This is the main movement method that ensures even coverage with HIFU.

• Tight contact

Place the black surface of the cartridge fully against the skin for maximum contact.

• Movement

Line movement: Start at the outer edge of the marked area and slowly slide the device outwards. Strive for one shot every 2 millimeters.

Moving to a new zone: Once you have completed this cycle (out and in) along the particular line, you need to move the unit a little further down or to the side to start the next line.

Avoiding repetition: It is important not to treat the same area multiple times in one pass to avoid excessive thermal exposure.

• Precision

When you reach the marked boundaries of nerve pathways (such as the mandibular nerve), you should stop moving and head in another direction instead of crossing directly over them.

Start with the setup 1Hz (one shot per second). This gives you better control over the placement of the shots and allows you to monitor your skin's reaction in real time.

Since you have an unlimited number of pulses, there is no need to rush. You can work carefully and at your own pace using the speed settings from 1Hz or 2Hz.

3. Specific technique for treating the lower jaw (the „cheek“ area)

If your goal is to tighten loose skin along your jawline, there is one „trick“ to keep you safe:

• With two fingers lift the skin up (about 2.5-5 cm above the bone).
• Slide the device along the raised skin, just above the bone.
• This technique allows you to treat the tissue effectively without hitting the bone directly, which would only cause unnecessary discomfort.

4. Follow your feelings

Your body will let you know if everything is okay. Normal sensations include:

• Warm feeling and/or slight pricking.
• Feeling of tightness in the treated area.

Plan and schedule for long-term results

To get the collagen „buildup“ effect, follow this schedule:

Frequency: Maximum once a week.

Intensity: Between 600 and 1200 shots per session, depending on the area (face and/or neck).

Course: Full cycle of 8 to 12 weeks, then move to maintenance once every 4 to 6 weeks.

Documenting progress: The results of working with ultrasound develop gradually, with the full transformation taking between 2 and 3 months. The photos will help you see improvements in skin density and vitality that are too subtle to be noticed by daily looking in the mirror. You can do clear "before" and "after" photos„ once a week.

Authenticity guarantee

Medicube Age-R High Focus Shot is a serious solution for long-term preservation of youthful contour and skin density at home. Its combination with the brand's specialized gel Medicube Booster Gel guarantees the necessary conductivity and provides maximum comfort for the skin during the entire procedure. To be sure that you are investing in an original product with a valid warranty, we recommend that you trust the official brand store on Amazon. This way you avoid the risks of reselling by third parties and receive complete security during delivery, as well as direct assistance from the manufacturer if necessary.

Links to products on Amazon and additional information: